 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Full Color Chip LED Lamps Part Number: AL-HUBG6B433T Package outlines & Re-flow Profile Reflow Temp/Time Soldering iron Basic spec is 5sec when 260. If temperature is higher, time should be shorter (+10 -1sec ).Power dissipation of iron should be smaller than 15W, and temperatures should be controllable .Surface temperature of the device should be under 230 . ITEM Resin (mold) Lens color Printed circuit board Dice For Reflow Soldering Emitted color MATERIALS Epoxy Water Clear BT AlGaInP InGaN InGaN Brilliant Red Brilliant Green Super Blue NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerances are 0.1mm (0.004inch) unless otherwise noted. 3. Polarity referring onto the cathode mark is reversed on the red. 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T ELECTRO-OPTICAL CHARACTERISTICS Parameter Forward voltage Luminous intensity Emitted Color R G B R G B R G B R G B R G B R G B R G B (TA=25) Unit V Value Test Symbol Condition MIN. TYP. MAX. IF=20mA VF - - - 90 112 45 2.0 3.4 3.5 140 180 70 632 518 468 624 525 470 20 30 30 60 100 100 60 110 110 2.6 3.8 4.0 180 210 100 IF=20mA IV mcd p IF=20mA d - - - Wavelength - - - nm Spectral Line Half-Width Peak pulsing current (1/10 duty f=1kHz) IF=20mA nm IF=20mA IFP mA Power Dissipation IF=20mA PD mW Absolute maximum ratings Parameter Symbol 21/2 IF VR IR Top Tstg Value 120 25 5 100 (TA=25) Unit Viewing angle at 50% Iv Forward current Reverse voltage Reverse current Operating temperature range Storage temperature range Deg mA V A 2007/6/13 -40 ~+80 -40 ~+85 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Test items and results of reliability NO 1 Item Solder Heat Test Conditions TEMP2605 H+85 30min 5min L-55 30min H+100 5min 10set L-10 5min TEMP100 Test Sample Size Ac/Re Hours/Cycle 5 Sec. 76 PCS 0/1 2 Temperature Cycle 50 CYCLES 76 PCS 0/1 3 Thermal Shock 50 CYCLES 76 PCS 0/1 4 High Temperature Storage 1000 HRS 76 PCS 0/1 5 Low Temperature Storage TEMP-55 1000 HRS 76 PCS 0/1 6 DC Operating Life IF=20mA 1000 HRS 76 PCS 0/1 7 High Temperature / High Humidity 85 / 85%RH 1000 HRS 76 PCS 0/1 Refer to reliability test standard specification for in this line. 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Typical Electro-Optical Characteristics Curves - Red 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Typical Electro-Optical Characteristics Curves - Green 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Typical Electro-Optical Characteristics Curves - Blue 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HUBG6B433T Precautions For Use 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 2007/6/13 |
Price & Availability of AL-HUBG6B433T
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |